SAE J1100 DOWNLOAD

SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Akirg Kesida
Country: Russian Federation
Language: English (Spanish)
Genre: Science
Published (Last): 26 September 2007
Pages: 169
PDF File Size: 5.35 Mb
ePub File Size: 9.4 Mb
ISBN: 560-5-63531-529-2
Downloads: 36732
Price: Free* [*Free Regsitration Required]
Uploader: Kizahn

A set of shoe-type boxes H-boxes are optionally used with the Standard Luggage Set. Use appropriate value in denominator for metric English units. For vehicle with more sae j1100 three seats, specify seat location along with dimension. Criminal penalties may aae for sae j1100.

The right pivot is with the right foot lined up on the accelerator and the left pivot is with the left foot on the floor in line with the clutch pedal.

This measurement accounts for adjustments independent of track rise. The forward limit is the rear side of the second seatback or the sae j1100 third seat. If the accelerator is depressed, j11000 manufacturer shall place foot flat sae j1100 pedal and note the depression of the pedal.

They may be loosened and moved to the limits of the attaching hardware and then retightened to attain the most advantageous position. Sae j1100 from subsequent Standard J1100 Sets may be used when the previous set is placed in the Luggage Compartment.

Any portion of this mm by mm area around the SgRP in side view below and behind the seat cushion and wae back sae j1100 is excluded. All interior dimensions for designated seated positions are defined on the Y-plane centerline of the occupant, unless otherwise defined in the dimensions definition.

Read Also:  MICROPROCESSOR 8086 BY SUNIL MATHUR PDF DOWNLOAD

They sae j1100 included in an effort to harmonize world-wide vehicle dimensioning practices and to permit accurate comparison of domestic and off-shore vehicle dimensions. V1 Sae j1100 Capacity 9. H Seat Cushion height – front 6. The Torso Line is parallel sae j1100 the straight flat portion of the lower back on the torso and is used j11100 facilitate the definition of torso angle. Sae j1100 front wheels eae be positioned in the straight-ahead position.

Descriptions and sizes of the luggage pieces are detailed in Table 1. Independent vertical adjustment, if provided, is not included.

Dimension Revised Section No.

The Luggage Compartment Lid or access door must close and lock freely without forcing or excessive slamming with ase of the luggage in place in the compartment.

All head restraints shall be in the stowed position and considered part of the seat. If no arm rest sae j1100 provided at the designated sar plane, use a sae j1100 of 1 80 mm above the SgRP. In case of dual rear axles, the dimension shall be to the midpoint of the centerlines of the rear wheels. Cargo Volume Index— Input values are mm inches.

Full text of “SAE J Motor Vehicle Dimensions”

Scope— This SAE Recommended Practice defines a uniform set of interior and exterior dimensions for passenger bars, multipurpose passenger vehicles, and trucks.

The dimension shall be at height of the cargo floor surface, if floor surface at engine cover sae j1100 above cargo sae j1100 surface, then length is taken at floor to engine cover intersection height.

Read Also:  TRANSISTOR S8550 DOWNLOAD

For heavy trucks, sae j1100 weight does not include engine fuel. For rear-facing third seat, measure from the trimmed seat back at a height tangent to the top of the third Seat Cushion surface, rearward to the interior sae j1100 closure.

SAE J1100: Motor Vehicle Dimensions

L Cab length 7. When only one outside mirror is standard, the dimension will be to the zero “Y” plane. Is the reference point employed to position the two-dimensional drafting template with the 95th percentile leg described in SAE J If there is a step, the dimension is measured vertically from the ground to the first step entering the vehicle. TL and TH dimensions from 2 through 5 sae j1100 only when vertical adjustment is sae j1100 independent of track rise with forward movement.

Refer to Section A minus – dimension indicates that the brake pedal is lower than the accelerator pedal. If the second seat is adjustable, it should be positioned sae j1100 the SgRP and at a back angle as specified by the manufacturer.

All dimensions are measured to the base vehicle and do not include Sae j1100 Production Options RPO or accessory parts, unless defined by the dimension definition. Design H-Point Travel Path